Spray Mix Calculator

Enter tank water and the label dose — get the exact chemical per tank. E.g. a 16-litre tank at 2 ml/L needs 32 ml.

Calculation mode
Chemical unit
L

A knapsack sprayer usually holds 16 litres — enter your own tank size

Enter the label dose — e.g. 2 ml per litre

Amount printed on the packet/bottle (same unit as the dose)

Chemical per tank

32 ml

Chemical per tank
32 ml
Water per tank
16 L
Packets per tank
0.32 packets

Mix 32 ml of chemical into 16 litres of water per tank.

Follow the label dose; wear a mask and gloves, never spray against the wind.

How this was calculated
  1. Chemical per tank = 16 × 2 ml = 32 ml
  2. Packets needed = 32 ÷ 100 = 0.32 packets

How to use

  1. Pick the mode — “Per tank” for one tankful, “Per packet” for the whole packet.
  2. Set tank capacity in litres, the label dose per litre, and the unit (ml/g).
  3. Enter the packet size — the result shows chemical per tank, packet fraction and total mix.

Formula

Chemical per tank = tank water (litres) × dose (ml/g per litre) Packets needed = chemical per tank ÷ packet size Total mix (litres) = packets × packet size ÷ dose Tanks filled = total mix ÷ tank water

  • The dose unit and packet unit must match (both ml, or both g).
  • Water is always in litres — 1 litre ≈ 1,000 ml.

Worked example

16-litre tank, dose 2 ml per litre, 100 ml packet:

Chemical per tank = 16 × 2 = 32 ml. Packets needed = 32 ÷ 100 = 0.32 packet (one packet covers about 3 tanks).

Mixing 2 packets (100 g each) at 2 g per litre:

Total mix = 2 × 100 ÷ 2 = 100 litres = 100 ÷ 16 = 6.25 tanks (6 full tanks + 4 litres).

Safety — read first

  • Follow the label dose; wear a mask and gloves, never spray against the wind.
  • Keep children and animals away while mixing; never throw empty packets into ponds or canals — bury them or use a designated collection point.
  • After spraying, wash hands and face with soap and wash work clothes separately.

What to know in Bangladesh

  • Verify the tank markings: moulded litre marks are often off — check once with a bucket.
  • Use clean water: muddy or saline water weakens the chemical. Rinse the tank well after herbicide sprays.
  • Hired spraying: when spraying others’ land, bill labour and chemical separately.
Details: calibrating with a water-only test run

On a new plot or with a new nozzle, first spray plain water with no chemical. Note how much land (how many katha) one full tank covers — that is your spray rate.

Say 16 litres covers 8 katha. Then one bigha (20 katha) needs 16 ÷ 8 × 20 = 40 litres = 2.5 tanks. Multiply that water by the label dose to get the total chemical — no guessing, no waste.

Walking speed and nozzle pressure change coverage, so keep a steady pace and clean nozzles.

Frequently asked questions

How many litres does a knapsack sprayer hold?

The common backpack (knapsack) sprayer in Bangladesh holds 16 litres; smaller models hold 8–10 litres. Check the marking on your tank and enter it — do not just assume 16.

Morning or evening — when is spraying best?

After the dew dries in the morning (9–11 am) or in soft afternoon sun (3–5 pm). Harsh midday sun dries the chemical too fast and lowers effectiveness, and strong wind drifts it away. Never spray against the wind.

How long after spraying before harvest?

That is the pre-harvest interval — from a few days to a few weeks depending on the chemical. There is no single number; follow the waiting period printed on the label for your crop.

ml or g — which unit for the dose?

Liquid formulations (EC, SL) are measured in ml, powders and granules (WP, SP) in grams. Use whichever unit the label dose is written in.

Will a higher-than-label dose give better results?

No — overdosing can burn leaves, build pest resistance, cost more and harm the environment. If it does not work, change the product on an agriculture officer's advice instead of raising the dose.

Also searched as

sprayer tank dose calculator · pesticide mix per litre · knapsack sprayer calibration · 16 litre tank pesticide dose