Stair Estimator

Enter the floor height. A 10 ft floor with 6″×10″ steps needs 20 risers — 10 + 10 dog-legged flights and ≈ 44.52 cft of concrete.

Stair type
ft
in

Each step height — usually 6″

in

Each step depth (foot space) — usually 10″

ft
in

Sloped slab under the steps — usually 5″

Concrete and materials (1:2:4)

44.52 cft

Steps (risers)
20
Actual riser
6 in
Flights
10 + 10 risers
Going length (without landing)
15 ft
In waist slab
26.29 cft
In step triangles
13.13 cft
In landing
5.1 cft
Cement
7.8 bags
Sand
19.59 cft
Aggregate
39.18 cft
Comfort check (2R+T)
22 in

This stair needs 20 steps and about 44.52 cft of concrete.

How this was calculated
  1. Risers = height ÷ riser = 120 ÷ 6 → 20; actual riser 120 ÷ 20 = 6.
  2. Going = tread × count = 10 × treads = 15 ft.
  3. Concrete = waist 26.29 cft + steps 13.13 cft + landing 5.1 cft = 44.52 cft.
  4. 1:2:4 mix: dry = 44.52 cft × 1.54 = 68.56 cft; cement = 68.56 cft ÷ 7 = 9.79 cft = 7.8 bags.

How to use

  1. Enter the floor-to-floor height in feet (usually 10).
  2. Give the riser (usually 6″) and tread (usually 10″).
  3. Pick the stair width, waist slab and type (dog-legged/straight).

Stair formulas

What Formula Example (10 ft, 6″×10″, dog-legged)
Risers height ÷ riser (rounded up) 120 ÷ 6 = 20
Flights half + half around a landing 10 + 10
Waist thickness × width × slope (per flight) two flights ≈ 26.29 cft
Steps ½ × tread × riser × width × 18 ≈ 13.13 cft
Landing width × width × thickness 3.5 × 3.5 × 5″ = ≈ 5.10 cft
Total waist + steps + landing ≈ 44.52 cft (≈ 7.84 cement bags)

Examples

10 ft floor, dog-legged: 6″×10″ steps give 20 risers (true 6″), 10 + 10 flights, 7.5 + 7.5 ft of going; concrete 26.29 + 13.13 + 5.10 = ≈ 44.52 cft; at 1:2:4 cement ≈ 7.84 bags, sand ≈ 19.59, aggregate ≈ 39.18 cft.

Same height, straight stair: one flight with 19 treads of going (≈ 15.83 ft), no landing — ≈ 41.16 cft total.

What to know in Bangladesh

  • Dog-legged is the standard: two flights plus a mid landing for homes — saves space and climbs easily.
  • Usual sizes: 6″ riser, 10″ tread, 3.5 ft wide, 5″ waist — use the drawing when it differs.
  • Railing and finishes are extra: this is concrete-and-mortar only; railing and tile/marble finishes add on top.
More: slope and landing

Flight slope = √(going² + rise²). At 7.5 ft of going and 5 ft of rise the slope ≈ 9.01 ft — waist concrete follows this slope.

The landing defaults to the stair width square (3.5 × 3.5 ft) at waist thickness. Add extra for bigger landings per the drawing.

Frequently asked questions

How is the step count found?

Risers = height ÷ riser, rounded up. 120″ ÷ 6″ = 20 risers, with one fewer tread.

How does a dog-legged stair split?

Two flights around a mid landing — 10 + 10 for 20 risers. The landing replaces one tread, so the going holds 18 treads.

What goes into the concrete?

Three parts: flight waist slabs (thickness × width × slope), step triangles (½ × tread × riser × width × count) and the landing.

What is 2R+T?

A comfort gauge: 2 × riser + tread. Steps of 6″×10″ give 22″ — the usual Bangladeshi stair.

Where is the steel?

Stair steel (main + distribution bars) follows the drawing; get the concrete volume here and weigh bars in the rod calculator.

Also searched as

staircase step calculation · dog-legged stair concrete · riser tread formula